DC7V-35V to DC1.25V-30V LED Driver Charging Constant Current Voltage Step Down Buck Power Supply Module
34
Direct purchase from the factory 
Idaniloju sisan
Ẹbun ọfẹ
Ilana gbigbe
Ilana padaẸbun Ọfẹ
Kaabọ si Roymall, oju opo wẹ ẹbun rẹ. A dupẹ lọwọ rẹ, a si pese ẹbun ọfẹ pẹlu eyikeyi rira. Ṣetan lati ṣawari akojo wa? Yẹra ni koko wa, fi aṣẹ rẹ sii, ki o si gba ẹbun ọfẹ rẹ.Ilana Gbigbe
A nṣe awọn aṣẹ laarin ọjọ 2.Gbigbe deede jẹ ọjọ 5-7.Akoko gbigbe le yatọ da lori ibudo.1. Ilana Pada
A gba nikan awọn nkan ti a ra lati roymall.com. Awọn ẹbun ọfẹ ko le pada. Nkan gbọdọ jẹ ailohunsi ati ni apoti atilẹba.A nṣe awọn pada laarin ọjọ 3-5 lẹhin gbigba.Awọn nkan aṣa ko le pada.Kan si wa: service@roymall.com tabi Whatsapp: +86193598494712.Ilana Isanwo
Iwọ yoo gba isanwo lẹhin gbigba nkan. A ko san owo gbigbe pada.Kan si wa: service@roymall.com tabi Whatsapp: +8619359849471
Feature:
n
nThis module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable.
nThis module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV!
nThis module uses machine placement, reflow soldering.
nThis module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V.
nModule indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module.
n
nDescription:
n
nNature of the module: Non-isolated step-down module
nRectification: Non-synchronous rectification
nInput voltage: 7V - 35V
nOutput voltage: 1.25V - 30V
nOutput current: Adjustable, 3A (maximum)
nTransfer efficiency: 92% (maximum)
nSwitching frequency: 150KHz
noutput ripple: 50mV (maximum) 20M Kbps
nLoad regulation: ±0.5%
nVoltage regulation: ±2.5%
nOperating temperature: -40°C to +85°C
nDimension: 48 x 23 x 14mm (L x W x H)
n
nBattery charging method:
n
n1. Make sure the battery float voltage and charging current, the module input voltage;
n2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value;
n4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment)
n5. Adjustment constant potentiometer allows the output voltage reaches the float voltage;
n6. Connected to the battery and try to charge.
n(1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.)
n
nLED constant current driver using method:
n
n1. Make sure that the drive LED operating current and maximum working voltage;
n2. Adjustment constant potentiometer, output voltage adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current;
n4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED;
n5. Connect LED, test machine.
n(1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.)
n
nPackage included:
n
n1 x Buck module
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
nThis module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable.
nThis module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV!
nThis module uses machine placement, reflow soldering.
nThis module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V.
nModule indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module.
n
nDescription:
n
nNature of the module: Non-isolated step-down module
nRectification: Non-synchronous rectification
nInput voltage: 7V - 35V
nOutput voltage: 1.25V - 30V
nOutput current: Adjustable, 3A (maximum)
nTransfer efficiency: 92% (maximum)
nSwitching frequency: 150KHz
noutput ripple: 50mV (maximum) 20M Kbps
nLoad regulation: ±0.5%
nVoltage regulation: ±2.5%
nOperating temperature: -40°C to +85°C
nDimension: 48 x 23 x 14mm (L x W x H)
n
nBattery charging method:
n
n1. Make sure the battery float voltage and charging current, the module input voltage;
n2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value;
n4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment)
n5. Adjustment constant potentiometer allows the output voltage reaches the float voltage;
n6. Connected to the battery and try to charge.
n(1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.)
n
nLED constant current driver using method:
n
n1. Make sure that the drive LED operating current and maximum working voltage;
n2. Adjustment constant potentiometer, output voltage adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current;
n4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED;
n5. Connect LED, test machine.
n(1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.)
n
nPackage included:
n
n1 x Buck module
n
n
n
n
n
n
n
n
n
n
n
n
n
n
