30.5×30.5mm GEPRC TAKER F722 OSD Flight Controller with 5V 12V BEC & 100A BL_S 3-8S 4in1 Brushless Stack for RC FPV Racing Drones
Direct purchase from the factory 
Idaniloju sisan
Ẹbun ọfẹ
Ilana gbigbe
Ilana padaẸbun Ọfẹ
Kaabọ si Roymall, oju opo wẹ ẹbun rẹ. A dupẹ lọwọ rẹ, a si pese ẹbun ọfẹ pẹlu eyikeyi rira. Ṣetan lati ṣawari akojo wa? Yẹra ni koko wa, fi aṣẹ rẹ sii, ki o si gba ẹbun ọfẹ rẹ.Ilana Gbigbe
A nṣe awọn aṣẹ laarin ọjọ 2.Gbigbe deede jẹ ọjọ 5-7.Akoko gbigbe le yatọ da lori ibudo.1. Ilana Pada
A gba nikan awọn nkan ti a ra lati roymall.com. Awọn ẹbun ọfẹ ko le pada. Nkan gbọdọ jẹ ailohunsi ati ni apoti atilẹba.A nṣe awọn pada laarin ọjọ 3-5 lẹhin gbigba.Awọn nkan aṣa ko le pada.Kan si wa: service@roymall.com tabi Whatsapp: +86193598494712.Ilana Isanwo
Iwọ yoo gba isanwo lẹhin gbigba nkan. A ko san owo gbigbe pada.Kan si wa: service@roymall.com tabi Whatsapp: +8619359849471Feature:
1. Uses the mainstream STM32F722 chip
2. Equipped with the latest 42688-P gyroscope
3. 16M onboard black box storage
4. Integrated LC filter
5. Upgraded Type-C USB interface
6. Directly plugs into the DJI Air Unit
7. Paired with the TAKER H100_8S_BLS 100A 4IN1 ESC, providing a smooth flying experience
8. Simple and efficient installation method with shock absorbers for stable gyroscope performance
9. Dual independent BECs: 12V@3A and 5V@3A
10. Supports 8S Lipo batteries
11. Support direct insertion of 8 motors
Specification:
Brand: GEPRC
Model: TAKER F722 BLS 100A 3-8S STACK
Model | Specification |
TAKER F722 8S Flight Controller | MCU: STM32F722 IMU: ICM42688-P(SPI) Air Unit Connection: Direct plugs into DJI Air Unit Black Box: 16M onboard USB Interface: Type-C Barometer: Supported OSD: BetaFlight OSD w/ AT7456E chip BEC: 5V@3A,12V@3A dual BEC Firmware Target: TAKERF722SE Dimension: 38.5u00d738.5mm, Mounfing Hole Size: 30.5u00d730.5mmuff0cu03c64mm hole becomes u03c63mm after using a silicone shock-absorbing circle Input Voltage: 3-8S LiPo UART: 6 UARTs Power Filter: Integrated LC filter Weight: 8.1g Includes |
TAKER H100_8S_BLS 100A 4IN1 ESC | Input Voltage: 3-8S Lipo Ammeter: Support Calibration value: 200 Continue Current: 100A Burst Current: 105A (5 seconds) Support Protocol: Dshot 150/300/600 Size: 56.3*61.1 mm; hole: 30.5u00d730.5 mm; u03c64 mm hole becomes u03c63mm after using the silicone shock-absorbing ring. Weight: 28.8g Target: B_X_30 |
Package Included:
1 x FC board
1 x ESC board
1 x Capacitor
1 x DJI O3 3-in-1 connection cable
2 x FC adapter cable
1 x sh1.0 4pin silicone cable
1 x Camera connection cable
1 x VTX connection cable
1 x XT90 power cable
4 x M3*30 screws
4 x M3*25 screws
8 x Nylon nuts
12 x Silicone anti-shake pads
