Mateksys MR24-30 mLRS (MAVLink long range system) firmware MAVLink 30dBm RF power 2.4GHz Receiver for FPV Drone
Direct purchase from the factory 
Idaniloju sisan
Ẹbun ọfẹ
Ilana gbigbe
Ilana padaẸbun Ọfẹ
Kaabọ si Roymall, oju opo wẹ ẹbun rẹ. A dupẹ lọwọ rẹ, a si pese ẹbun ọfẹ pẹlu eyikeyi rira. Ṣetan lati ṣawari akojo wa? Yẹra ni koko wa, fi aṣẹ rẹ sii, ki o si gba ẹbun ọfẹ rẹ.Ilana Gbigbe
A nṣe awọn aṣẹ laarin ọjọ 2.Gbigbe deede jẹ ọjọ 5-7.Akoko gbigbe le yatọ da lori ibudo.1. Ilana Pada
A gba nikan awọn nkan ti a ra lati roymall.com. Awọn ẹbun ọfẹ ko le pada. Nkan gbọdọ jẹ ailohunsi ati ni apoti atilẹba.A nṣe awọn pada laarin ọjọ 3-5 lẹhin gbigba.Awọn nkan aṣa ko le pada.Kan si wa: service@roymall.com tabi Whatsapp: +86193598494712.Ilana Isanwo
Iwọ yoo gba isanwo lẹhin gbigba nkan. A ko san owo gbigbe pada.Kan si wa: service@roymall.com tabi Whatsapp: +8619359849471Mateksys MR24-30 mLRS (MAVLink long range system) firmware MAVLink 30dBm RF power 2.4GHz Receiver for FPV Drone
Specifications:
Stm32g431kb, mLRS Firmware
Lora sx1281 with tcxo
Pa/lna SKY68383-11
RF frequency: 2.4GHz ism
RF power: 13dbm (min) /20dbm/24dbm/27dbm/30dbm (1000mw)
Antenna connection: IPex-MHF-1
Tx1/rx1: bidirectional all serial Mavlink
Tx2: rc out (crsf or sbus)
A button for dfu mode and bind
Power supply: 4.5-13V DC @ "V" Pad
Power loss: 360ma @ 5v in (50hz, 30dbm)
Circuit board size: 28x21mm
Weight: 4.5g w/antenna
Guided status:
[Red flashing 2hz], not connected to transmitter
[Green flashing 1hz], connected to transmitter
[Red and Green alternating], binding mode activated
Binding:
After switching on, press the bind button (for about 4 seconds) on the receiver. In binding mode, the green and red LEDs flash alternatively at approximately 2.5 Hz.
https://github.com/olliw42/mLRS-docu/blob/master/docs/BINDING.md
Firmware:
Mlrs https://github.com/olliw42/mLRS/tree/v1.3/firmware/release-matek
Goals:
RX receiver: rx-matek-mr24-30-g431kb
Tx module mode: tx-matek-mr24-30-g431kb-default
Tx siktelem mode: tx-matek-mr24-30-g431kb-siktelem
Tips:
If you set the RF power >=500mw, it is recommended to attach the heatsink to the bottom of the circuit board. The gaps between the slats can be used for mounting with m3 screws
Package included:
1x mR24-30
1x 15cm Ipex Mhf1 Sleeve Dipole Antenna
1x 20*20*6mm Heatsink
